|
|
perfect rotary engine
Posted by Anonymous . updated on 2/26/2009
Can you help me in finding suitable invester or pramoter for this invention?
Important features of the Engine:
---------------------------------
This rotary engine has some unique features that makes this engine light years ahead of conventional IC engines. One is separate sides for intake (charge) and exhaust gas which is suitable for HYDROGEN FUEL, Which is the fuel of new century.
In this engine 4 stages of Atkinson cycle (a more efficient varient of otto cycle except expansion ratio different from compression ratio) are optimized for better efficiency 2 of them are shown in PV diagram.
1.) Since exhaust side and intake side are separate intake side is cooler than exhaust side and less heat is transferred from rotor to charge. Since charge is cooler higher compression ratio can be achieved.
2.) Since constant volume heat addition is possible by increasing the width of rotor’s one lobe, ignition before compression stroke ends, is not necessary, so there will not be any back pressure due to combustion. During ignition and constant volume heat addition, volume of charge is considerably low this results in faster flame distribution (since fuel particles in the mixture are closer to each other.) and faster and better combustion results. This also results in higher temperature with minimum fuel. This will increase efficiency. also distance from spark plug to most distant fuel particle is minimum at the time of ignition, compared to other engine architectures. Since surface area is minimum during cumbustion less heat is lost to the surroundings.
3.) As you can sea in torque chart, most of heat energy is converted into mechanical work earlier than in piston engine. So less heat will be transferred to the surroundings compared to piston engine during power stroke. More than that expansion ratio is decreased without changing compression ratio (exhaust volume is higher than intake volume) more heat will be converted to work which is not possible in piston or Wankel engine.
4.) In exhaust stroke due to lower expansion ratio pressure will be almost equal to atmospheric pressure. So no valve opening before expansion stroke ends is required. This results in less back pressure during exhaust without losing any expansion.
............................................................
Since combustion takes place faster due to constant volume heat addition we get more work due to earlier expansion of gases and full power stroke with entire fuels energy. In piston engine combustion finishes only after 10-20 degree of rotation from TDC. So only a part of the fuel’s energy is getting during TDC to 10-20 degree of rotation.
Since constant volume heat addition is possible combustion temperature will be very high so better, faster and complete combustion results
Since combustion takes place at fairly high temperature all fuel particles are burned faster even near the surface of combustion chamber.
Don’t forget that higher combustion temp is only because of the constant volume heat addition, all other factors like air/fuel ratio and compression ratio are kept same.
As you know increasing T3 (combustion temperature) increases efficiency
..................................................................
Another is we can increase expansion ratio without changing compression ratio(since intake and exhaust area are separate). As we know efficiency is directly proportional to compression ratio. Efficiency is also directly proportional to expansion ratio. Since it is impossible to increase compression ratio beyond certain limit. Then only major way to increase efficiency is to increase expansion ratio. This is possible in my engine.
For example an engine having compression ratio 8:1 and expansion ratio 1:10 have higher efficiency than engine with compression ratio 8:1 and expansion ratio 1:8.
Another is flow characteristics. In piston engines there are
3 stages where gases inside the cylinder make 180 degree turn.
But in my engine there is only one which is at combustion chamber.
This is good for combustion because turbulence is good for faster flame propagation.
As for lubrication major force is on cam rather than on rotor, there (on the link between valve and cam)I provided rollers for minimum friction. Stoppers are touching the rotor with the slight force of spring provided in the valve assembly whose traveling distance is only 2 millimeter.
Only one cam is required to operate 4 valves, cam also acts as fly wheel.another important thing about cam is it is circular and pivot is at center so less vibration results. guides of valves are running on side ward projecting rails on the cam. Since the rail is locked between the two rollers, when valve has to be accelerated from zero velocity, the cam pushes valve and when valve has to be stopped (deaccelerated ) the valve pushes cam(flywheel). so we get extra enrgy given to move the valve. Geometry of rails are a combination of parabolic spirels.
Answers (3)
| |
|
JimIvey
|
One of the communities always interested in innovative power solutions is the experimental aircraft community. http://www.eaa.org/These guys have puts rotary engines in airplanes: http://www.atkinsrotary.com/There's substantial interest in rotaries in airplanes due to near bullet-proof reliability and the redundancy for safety (you can run each rotor independently of the others -- so two rotors is like two-engine reliability and three rotors is even better). Here's another link: http://home.earthlink.net/~rotaryeng/Internal combustion aircraft engines are horribly out-dated -- after many decades of the research philosophy, "if it ain't broke, don't fix it." Now, I/C aircraft engines are becoming increasingly perceived as "broke" -- so there's much research and activity around rotaries, diesels, FADEC systems, etc. A lot of the research is based on the believe that avgas (aviation gas) -- which is low lead, not no lead -- is not going to be around much longer. Anyway, I think you'll find interested parties in those communities. Good luck!
|
|
| |
|
P.Nagel
|
I doubt you'll find 'investers' or 'pramoters' anywhere.
Where can I find this sea in torque chart?
The description of this "perfect engine" looks like it was copied from a piece of spam. I hope you weren't duped into giving someone money for this garbage.
|
|
| |
|
M. Arth...
|
Even if you had foolproof patent claims, it would not be easy to sell something new particuarly if it takes big money to start up and test.
|
|
Related Questions
 |
so i have an idea, but i dont know if it is patentable. so i should talk to an intellectual property lawyer, right? but how can i trust him? like lets say i tell him my idea but i chose not to work with him,... Read More |
|
i developed my own system of self defense years ago and it is in use. I gave it a name. What do I need to do to legally protect myself from others that would try to lay claim to it? Read More |
|
i am a 21 year old who has come up with a world changing invention that can potentially save thousands of lives and i need to know what i have to do to make sure no one steals my idea. i have never invented ... Read More |
|
I developed an innovative bioanalytical methodology using existing instrumentation but customized the instrument configuration and wrote a macro for the automation, while working as an employee of a biotech ... Read More |
|
Ive got a new idea and I don't know where to start! I have contacted a few places e.g Patent & Trademark of America..but people are asking me to send my idea in.my question is who can i trust? and i dont kno... Read More |
|
Previous question: Patenting IDEAS >>
- Patent Express is the fastest and easiest way for an individual inventor to file a U.S. Patent or Trademark Application.
- Patent Express fills the gap for those who cannot afford a U.S. patent attorney or agent, but want to have their patent drafted and issued.
- Patent Express is backed by a 100% money back guarantee.
|